For screen reader problems with this website, please call480-503-34004 8 0 5 0 3 3 4 0 0Standard carrier rates apply to texts.

Sound Effects

Sound Effects

480-503-3400

Crestron® 4 Channel High-Inrush Switch Module

Model #: CLX-4HSW4

At a Glance

Crestron® 4 Channel High-Inrush Switch Module with 4 speeds and 120 volts

WarningProposition 65 Warning for California Residents
Crestron® 4 Channel High-Inrush Switch Module

Features

Indoor/OutdoorIndoor

General Specs

Product Weight (lbs.)3
Width (in.)6.92
Depth (in.)3.43
Height (in.)7.59

Crestron® 4 Channel High-Inrush Switch Module

Model #: CLX-4HSW4
171785
Model #: CLX-4HSW4
Crestron
$99,999.00

Call for Best Price

At a Glance

Crestron® 4 Channel High-Inrush Switch Module with 4 speeds and 120 volts

Get to know this product.

Provides four channels of switching for 120 Volt residential and commercial lighting applications. Supports a full range of high-inrush, non-dimmable lighting loads. Installs in a CAEN or CAEN-MLO wall mount automation enclosure as part of a complete Crestron® centralized lighting control system.Photo shows module with terminal block on left. CLT-4HSW4 terminal block sold separately.Visit the Crestron® Lighting Fixture Compatibility page to find out which Crestron lighting devices have been tested and are compatible with third party lighting fixtures.The Crestron® CLX-4HSW4 is a four-channel, four-feed switch module designed for 120V lighting system applications. It installs in a CAEN or CAEN-MLO enclosure and provides control of non-dimmable lighting loads including LED, incandescent, fluorescent, magnetic low-voltage, electronic low-voltage, neon/cold cathode, and high-intensity discharge. It can also be used to switch motor loads. Individual feed capability provides four independent single-channel switches in one module space. Each channel is rated for 16 Amps, with a total module rating of 64 Amps when fed from four separate 20 Amp feeds.

Air-Gap Relays

    An air-gap relay on each channel output allows individual circuits to be serviced without disabling the entire module.

Silent Operation

    Low-maintenance convection cooling with over-sized heatsinks affords silent operation with no mechanical components to wear out.

Centralized Lighting Cabinet Installation

    Crestron CLX series lighting control modules are designed to be installed in a CAEN or CAEN-MLO wall mount enclosure. Available in a variety of sizes, CAEN and CAEN-MLO enclosures provide a scalable, high-density centralized lighting control solution for any-sized residence or commercial facility. A selection of CLX module types is offered to accommodate a wide range of load types and system configurations.

    Termination of high-voltage wiring to the CLX-4HSW4 module is facilitated using a CLT-4HSW4 terminal block, which is sold separately to enable termination of the wiring prior to installing the module. This terminal block mounts beside the module within the enclosure. Low-voltage control signals are bussed between each of the modules within an enclosure via a simple 5-wire link (interconnect jumpers included), which terminates to a single terminal block (model CAEN-BLOCK, sold separately) at the bottom of the enclosure.

Cresnet® Communications

    The CLX-4HSW4 interfaces with a Crestron control system (a.k.a., control processor or automation processor) via Cresnet. Cresnet is a simple 4-wire network bus that provides the communications backbone for a system of Crestron lighting dimmers, switches, keypads, shades, thermostats, and other devices.

Emergency Lighting Control

    The CLX-4HSW4 is UL® 924 and CSA® C22.2 No. 141-15 listed for use in controlling emergency lighting loads. In the event of a power failure, a contact closure from a power loss sensor (Crestron GLS-PLS-120/277, sold separately) activates the override mode in the CLX-4HSW4 to turn on each designated lighting load if it is off (assuming line power is supplied by a backup power source).

Key Features

    Four-channel high-inrush switch module for residential and commercial lighting applications

    Installs in a Crestron® CAEN or CAEN-MLO enclosure

    Supports on/off switching of LED, incandescent, fluorescent, magnetic low-voltage, electronic low-voltage, neon/cold cathode, and high-intensity discharge lighting loads

    Also supports on/off switching of 1/2 HP motor loads

    Individual feed inputs per channel

    Rated 16 Amps per channel, 64 Amps total (using four 20 Amp feeds), at 120 Volts AC

    Built-in air gap relay per channel

    Convection cooled for silent operation

    Closure-activated override mode

    UL® 924 and CSA® C22.2 No. 141-15 listed for emergency lighting control

    Crestron system integration via Cresnet®

    Easy termination using a CLT-4HSW4 terminal block (sold separately)

    CEC Title 24 2013 compliant

Specifications

General Specs

Product Weight (lbs.)3
Width (in.)6.92
Depth (in.)3.43
Height (in.)7.59

Features

Indoor/Outdoor:Indoor
WarningProposition 65 Warning for California Residents